收藏本站
MICROTORCH MT-5
CAP
WINDSHIELD
BOTTOM VIEW
Fig. 4
OFF-LOCK
SAFETY LOCKOUT
IGNITION BUTTON
MORE
GAS
LESS
GAS
LEVER
GAS FLOW VALVE STEM
Fig. 1
Fig. 2
Fig. 3
FLAME ADJUSTMENT
Specifications
To extinguish flame / Turn off gas flow
? From Normal Use: Release pressure from ignition button. Unit will shut
off immediately. (figure 2)
? From Hands free use: Slide hands free slide stem to full left position.
BODY
FUEL VIEW
FUEL ADJUSTMENT
Size dim.
Unit Weight
Internal tank pressure
Continuous burn time
75x32x21mm
45g
65 g/mm2 max
20 min. - one fill
Unit will shut off immediately (figure 3).
CAUTION:
1. Keep out of reach of children.
2. Do not touch flame guard when hot!
3. Butane gas is extremely flammable, please handle with care.
4. Always point away from eyes and body when igniting
Please read and understand
all warnings and instructions.
T o ignite unit (figure 2)
? Remove safety cap.
? Slide lockout lever to off position and hold in position while slowly
depressing ignition button.
? After a few attempts if no flame appears, fine tune the unit’s gas flow
and retry ignition step above.
T o adjust fuel flow (figure 4)
? Adjust the unit fuel flow by turning the black fuel flow adjustment wheel
at bottom of unit. A 1/4 inch turn CW/CCW will usually be all that is
needed. Note: Extreme caution must be taken not to over adjust fuel
flow. If you are unable to make proper adjustment, please call customer
service. As the gas is consumed, the gas flow can be adjusted periodi-
cally to ensure proper flame height. It is recommended that the user set
the flame height to 1/2 inch to 1 inch. If the flame height is set outside
these limits the fuel flow / flame may become unstable and cause
premature clogging or ignition failure.
Hands free mode (figure 3)
? To engage hands free mode follow ignition steps above and once the
unit is ignited, position slide stem button (found on backside of unit) to
or operating.
5. Do not store under direct sunlight or anywhere that will exceed
104°F/40°C.
6. Under no circumstances should you attempt to repair a damaged torch.
7. After using, let the tool cool down before storing.
Contains flammable gas under pressure. Do not use near sparks or open
flame. Do not puncture or incinerate container.
T o refuel unit. (figure 1)
? Make sure the unit is OFF and COOL to touch.
? Make sure the protective cap is on nozzle.
? Use only Master Ultratane ? butane to refuel unit, hold unit firmly with
filler valve pointing up. Place nozzle of butane canister down onto refill
valve and press butane canister down and up in short duration until fuel
tank is filled. Allow 2 -3 minutes for gas to stabilize after filling unit.
? Flame is invisible in direct sunlight. Use caution.
? Point away from face and body when igniting.
? Use in well ventilated areas.
? Always have a fire extinguisher/ bucket of water nearby work area.
? The tank contents are visible through the clear viewing port on the unit.
2420-18th Street, Racine, WI 53403 U.S.A.
PHONE: 262-633-7791 FAX: 262-633-9745
www.masterappliance.com
full right position. This will allow hands free operation of unit.
Designers and Manufacturers of Heat Tools
E-mail: sales@masterappliance.com
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MT-76K KIT TRIGRTORCH 3IN1 BUTANE TOOL
MUBW10-06A6 MODULE IGBT CBI E1
MUBW10-06A7 CONVERTER/BRAKE/INVERTER 1.9VCE
MUBW10-12A7 CONVERTER/BRAKE/INVERTER 2.3VCE
MUBW100-06A8 MODULE IGBT CBI E3
MUBW15-06A6 MODULE IGBT CBI E1
MUBW15-06A7 MODULE IGBT CBI E2
MUBW15-12A6 MODULE IGBT CBI E1
相关代理商/技术参数
MT5 1-10 制造商:IMO Precision Controls Ltd 功能描述:TERMINAL MARKERS NO. 1-10 5M
MT5 1-50-FAR 制造商:IMO Precision Controls Ltd 功能描述:TERMINAL MARKER 制造商:IMO PRECISION CONTROLS 功能描述:TERMINAL MARKER 制造商:IMO Precision Controls Ltd 功能描述:TERMINAL MARKER; Accessory Type:Terminal Block Marker; For Use With:Terminal Blocks; Legend:1 to 50; Pitch Spacing:0mm; SVHC:No SVHC (19-Dec-2012); Connector Type:Terminal Block Marker; Current Rating:0A; External Width:0mm; No. of ;RoHS Compliant: Yes
MT5 1-50-FAR 制造商:IMO Precision Controls Ltd 功能描述:TERMINAL MARKER
MT5/H- 功能描述:接线端子工具和配件 Marking Tag 5mm Horizntal(pk of 100) RoHS:否 制造商:Phoenix Contact 产品:Tools & Accessories 类型:End Bracket
MT5/H- - 功能描述:接线端子工具和配件 MARKING TAG Horizntal(pk of 100) RoHS:否 制造商:Phoenix Contact 产品:Tools & Accessories 类型:End Bracket
MT5/H-+ 功能描述:接线端子工具和配件 Marking Tag 5mm Horizntal(pk of 100) RoHS:否 制造商:Phoenix Contact 产品:Tools & Accessories 类型:End Bracket
MT5/H-0 功能描述:接线端子工具和配件 Markg Tag 5mm Horizntal(pk of 100) RoHS:否 制造商:Phoenix Contact 产品:Tools & Accessories 类型:End Bracket
MT5/H-1 功能描述:接线端子工具和配件 Marking Tag 5mm Horizntal(pk of 100) RoHS:否 制造商:Phoenix Contact 产品:Tools & Accessories 类型:End Bracket